Isa Dumanoglu

We report on the test beam results and calibration methods using high energy electrons, pions and muons with the CMS forward calorimeter (HF). The HF calorimeter covers a large pseudorapidity region ( $3\leq|\eta|\leq5$ ), and is essential for a large number of physics channels with missing transverse energy. It is also expected to play a prominent role in the measurement of forward tagging jets in weak boson fusion channels in Higgs production. The HF calorimeter is based on steel absorber with embedded fused-silica-core optical fibers where Cherenkov radiation forms the basis of signal generation. Thus, the detector is essentially sensitive only to the electromagnetic shower core and is highly non-compensating (e/h≈5). This feature is also manifest in narrow and relatively short showers compared to similar calorimeters based on ionization. The choice of fused-silica optical fibers as active material is dictated by its exceptional radiation hardness. The electromagnetic energy resolution is dominated by photoelectron statistics and can be expressed in the customary form as $\frac{a}{\sqrt{E}}\oplus{b}$ . The stochastic term a is 198% and the constant term b is 9%. The hadronic energy resolution is largely determined by the fluctuations in the neutral pion production in showers, and when it is expressed as in the electromagnetic case, a = 280% and b = 11%.

Extensive measurements have been made with pions, electrons and muons on four production wedges of the compact muon solenoid (CMS) hadron barrel (HB) calorimeter in the H2 beam line at CERN with particle momenta varying from 20 to 300 GeV/c. The time structure of the events was measured with the full chain of preproduction front-end electronics running at 34 MHz. Moving-wire radioactive source data were also collected for all scintillator layers in the HB. The energy dependent time slewing effect was measured and tuned for optimal performance.

Abstract As part of its HL-LHC upgrade program, the CMS collaboration is developing a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with ∼30,000 hexagonal silicon modules. Prototype modules have been constructed with 6-inch hexagonal silicon sensors with cell areas of 1.1 cm 2 , and the SKIROC2-CMS readout ASIC. Beam tests of different sampling configurations were conducted with the prototype modules at DESY and CERN in 2017 and 2018. This paper describes the construction and commissioning of the CE calorimeter prototype, the silicon modules used in the construction, their basic performance, and the methods used for their calibration.

We present the results of beam tests with high-energy (8–375 GeV) electrons, pions, protons and muons of a sampling calorimeter based on the detection of Cherenkov light produced by shower particles. The detector, a prototype for the very forward calorimeters in the CMS experiment, consists of thin quartz fibers embedded in a copper matrix. Results are given on the light yield of this device, on its energy resolution for electron and hadron detection, and on the signal uniformity and linearity. The signal generation mechanism gives this type of detector unique properties, especially for the detection of hadron showers: narrow, shallow shower profiles and extremely fast signals. These specific properties were measured in detail. The implications for measurements in the high-rate, high-radiation Large Hadron Collider (LHC) environment are discussed.

We present performance studies of a full-length prototype for the CASTOR quartz-tungsten sampling calorimeter, installed in the very forward region of the CMS experiment at the LHC. The response linearity and energy resolution, the uniformity, as well as the showers’ spatial properties in the prototype have been studied with electrons, pions and muons of various energies. A special study was also carried out for testing the light-output with a 90-degree cut of the quartz plates of the calorimeter. The data were taken during the CASTOR test beam at CERN/SPS in 2007.

We present the results of experimental studies of hadron showers in a copper/quartz-fiber calorimeter, based on the detection of Cherenkov light. These studies show that there are very significant differences between the signals from protons and pions at the same energies. In the energy range between 200 and 375 GeV, where these studies were performed, the calorimeter's response to protons was typically 10% smaller than the response to pions. On the other hand, the energy resolution was about 25% better for protons. In addition, the protons had a Gaussian line shape, whereas the pion response curve was asymmetric. These differences can be understood from the requirements of baryon number conservation in the shower development. They are expected to be present in any non-compensating calorimeter, to a degree determined by the e/h value.

We investigated the darkening of nine high OH− fibre types irradiated with 500MeV electrons from the Linac Injector of LEP (LIL) at CERN. The transmission of Xe light was measured in situ in the 350–800nm range. The induced attenuation at 450nm is typically 1.52±0.15dB/m for a 100Mrad absorbed dose. Two-parameter fits for darkening and recovery are presented. After irradiation the tensile strength remains essentially unchanged. For Polymicro quartz core fibres the tensile strength is typically 4.6±0.4GPa.

The Outer Hadron Calorimeter (HCAL HO) of the CMS detector is designed to measure the energy that is not contained by the barrel (HCAL HB) and electromagnetic (ECAL EB) calorimeters. Due to space limitation the barrel calorimeters do not contain completely the hadronic shower and an outer calorimeter (HO) was designed, constructed and inserted in the muon system of CMS to measure the energy leakage. Testing and calibration of the HO was carried out in a 300 GeV/c test beam that improved the linearity and resolution. HO will provide a net improvement in missing E T measurements at LHC energies. Information from HO will also be used for the muon trigger in CMS.

Due to an expected increase in radiation damage under super-LHC conditions, we propose to substitute the scintillator tiles in the original design of the hadronic endcap (HE) calorimeter with quartz plates. Quartz is proved to be radiation hard by the radiation damage tests with electron, proton, neutron and gamma beams. Using wavelength shifting fibers, it is possible to collect efficiently the Cherenkov light generated in quartz plates. This paper summarizes the results from various test beams, bench tests, and Geant4 simulations done on methods of collecting light from quartz plates, as well as radiation hardness tests on quartz material.

The first pre-production-prototype (PPP-I) of the quartz fibre calorimeter of the CMS detector has been tested at CERN. The calorimeter consists of quartz fibres embedded in an iron matrix. Results are presented on the energy resolution and on the signal uniformity of the prototype for electrons and pions and the signal uniformity and linearity.

The longitudinal and lateral shower profiles for 500MeV electrons in iron are studied using dosimetry and activation techniques. The results are compared with Monte Carlo simulations and other previously published data. The agreement between the data and the EGS4 simulation results is good; a simple shower profile parametrization of type kzα−1exp(−βz) does not represent the experimental data well at and around the shower maximum. The differences observed in the activation and dose profiles clearly show the role of photons in electromagnetic showers. The photon fraction increases as the shower develops deeper and they carry a larger energy fraction farther into the absorber. Photodisintegration reactions are responsible for the activation of the iron and we identified Mn54,Fe53 and Mn56 as more active isotopes among several others. These studies were performed for estimating the dose and its profile for the CMS quartz fiber calorimeter radiation damage work performed at LIL (CERN).

The experiments at the Large Hadron Collider (LHC) will have to deal with unprecedented radiation levels. In the large-rapidity regions, close to the beam pipe, these levels reach megagrays per year. The detectors to be installed in these regions, the HF Calorimeters, are designed to operate under these conditions. In this paper, we describe the results of studies in which a prototype calorimeter was exposed to radiation of the type and intensity expected at the LHC. These studies made it possible to estimate the effects of this radiation on the response and the resolution of the calorimeter as a function of time during LHC operation.

The synchronization and timing of the hadron calorimeter (HCAL) for the Compact Muon Solenoid has been extensively studied with test beams at CERN during the period 2003-4, including runs with 40 MHz structured beam. The relative phases of the signals from different calorimeter segments are timed to 1 ns accuracy using a laser and equalized using programmable delay settings in the front-end electronics. The beam was used to verify the timing and to map out the entire range of pulse shapes over the 25 ns interval between beam crossings. These data were used to make detailed measurements of energy-dependent time slewing effects and to tune the electronics for optimal performance.

CMS very forward calorimeter is based on a quartz fibre technology. The calorimeter prototype composed of two longitudinal segments was tested at CERN in 1996. We present the test beam data analysis of this prototype. It was shown that the mean values of responses for pions and electrons of the same energy could be equalised using the appropriate ratio of calibration constants for longitudinal segments. The beam test data were used to simulate the calorimeter response to hadron jets.

We present test-beam data analysis of a quartzfibre calorimeter prototype composed of a single active section with a passive absorber in front of it. The partial suppression of the electromagnetic showers leads to the equalization of the response to electrons and pions for a given depth of this passive section. Results are compared with the Monte-Carlo expectations.

The CMS‐CASTOR calorimeter is designed to study the very forward, baryon‐rich region in heavy ion collisions. Together with ZDC, it will make possible the covering of almost the whole angular region for CMS. CASTOR consists of quartz plates in a heavy metal matrix. Cherenkov light produced in the quartz plates will be detected by Hamamatsu R5380 Photomultiplier Tubes (PMTs). All the PMTs which will be used in the calorimeter have to be verified for gain and timing characterisation to have the performance required by CMS‐CASTOR Group before their installation into the calorimeter. We established a testing station at Cukurova University for this purpose. In the present paper we are going to give the anode dark current and gain measurements of these PMTs.

As part of its HL-LHC upgrade program, the CMS Collaboration is developing a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modules have been constructed with 6-inch hexagonal silicon sensors with cell areas of 1.1~$cm^2$, and the SKIROC2-CMS readout ASIC. Beam tests of different sampling configurations were conducted with the prototype modules at DESY and CERN in 2017 and 2018. This paper describes the construction and commissioning of the CE calorimeter prototype, the silicon modules used in the construction, their basic performance, and the methods used for their calibration.